Service History 14

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHW08

Near Pikeville, North Carolina 27863

Greg Glade

Job Details: 04/21/2026

Installed new evaporator motor and ice bucket. Ensured proper operation. Also cleared clogged defrost drain.

We serviced a

WHIRLPOOL COOKTOP GAS

Model GLT30146Q1

Near Newport, North Carolina 28570

Davon

Job Details: 04/21/2026

Unit not working. Confirmed that all igniter electrodes are working. There is no gas going to the unit. Front two burner valves are sticking, but appear to work. The valves are no longer available. If the valves being difficult to turn are an issue, the unit would need to be replaced.

We serviced a

MAYTAG DRYER

Model MED6230HW3

Near New Bern, North Carolina 28562

Davon

Job Details: 04/21/2026

Not heating. Found open heating element. Large amount of lint in dryer. Apparently poor air flow contributed to heating element failure. Replaced heating element and confirmed proper operation. Found air flow 7.1 mph. Cleaned vent and installed semi rigid vent behind dryer. Air flow improved to 21.4 mph. ; used 1 WP3387747 (HEATING ELEMENT) from stock

We serviced a

FRIGIDAIRE REFRIGERATOR TOP

Model FRT18L4JBP

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/20/2026

Customer reports clicking noise coming from fridge. Found noise is coming from defrost timer. Fridge still cooling and cycles when manually turning defrost timer. Would recommend replacement if any issues show in cooling.

We serviced a

FRIGIDAIRE REFRIGERATOR SID

Model FRSS26L3AF7

Near Havelock, North Carolina 28532

Davon

Job Details: 04/20/2026

Installed new condenser fan and confirmed proper operation. Unit has been cooling well since new evaporator fan was installed.

We serviced a

SAMSUNG REFRIGERATOR SID

Model RF22M9581SG/AA

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/20/2026

Installed new ice maker fan and ensured proper operation.

We serviced a

GE DISHWASHER

Model GDT226SSL1SS

Near Farmville, North Carolina 27828

Greg Glade

Job Details: 04/20/2026

Upon arrival to install new switch, found that the leak was coming from a small rusted out holes in the casing itself under the float switch. Customer opted to replace unit.

We serviced a

MIDEA WASHER

Model MLV45N1BWW

Near Havelock, North Carolina 28532

Davon

Job Details: 04/20/2026

Installed new control board and lid lock. Put clothes in and started cycle to get them wet. Then ran spin only cycle. Washer did not go out of balance and appears to be working correctly.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHB2740PP8A

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/20/2026

Installed new thermistor and ensured proper operation.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHW05

Near La Grange, North Carolina 28551

Greg Glade

Job Details: 04/20/2026

Customer reports water not working at door. Ice maker working fine. 120 vac at water valve. Water came not actuating at back. Failed water valves. Also recommended to customer to replace water filter in fridge as it has not been replaced in some time. ; ordrd 1 WPW10179146 (VALVE - DOUBLE COIL)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FGHS2631PF4A

Near Kinston, North Carolina 28504

Greg Glade

Job Details: 04/20/2026

Customer reports fridge not cooling and freezer not making cooler temp. Found that freezer has large sheet of ice on bottom. Cannot hear evaporator fan running either. ; used 1 04-90172ss-LF ( Ice maker line) from stock, ordrd 1 809069220 (EVAP FAN MOTOR (STANDARD TM - REAR WALL))

We serviced a

WHIRLPOOL RANGE

Model RF263LXTB3

Near Washington, North Carolina 27889

Davon

Job Details: 04/20/2026

Did not heat in bake mode per customer. On my arrival it heats up to 350F in several minutes. Bake element drawing 10.2 amps. Broil element heats up to 14.2 amps. No problems at this time. 30 day warranty on service call.

We serviced a

MAYTAG WASHER

Model MVWB865GW0

Near Jamesville, North Carolina 27846

Davon

Job Details: 04/20/2026

Customer reports that washer is not spinning. Found that unit does not spin in test mode. Agitator spins, but basket does not. Found that transmission is leaking. Bolt is rusted and wet on rotor. Diagnosed failed transmission and slider. F7E0, F2E1. ; ordrng 1 W11393685 (Transmission)

We serviced a

LG WASHER

Model WT7800CW

Near Kinston, North Carolina 28504

Greg Glade

Job Details: 04/20/2026

Customer reports PE error code. Found that pressure sensor connections are very corroded. Pressure sensor ohms out fine at 21 ohms. Would recommend replacement sensor and repairing wires. Would fix wires and heat shrink with new spades.

We serviced a

NORCOLD REFRIGERATOR

Model n/a

Near Aurora, North Carolina 27806

Davon

Job Details: 04/20/2026

Unit blinking no. co. and not cooling. After performing control board reset and correcting reversed neutral/hot ac supply unit appears to be working correctly. Drawing 2.3 amps in AC mode through AC heater wires.

We serviced a

ROPER DRYER

Model RED4516FW0

Near Kinston, North Carolina 28501

Greg Glade

Job Details: 04/17/2026

Customer reports dryer not spinning but still heating. Found broken dryer belt. Replaced dryer belt and ensured proper operation. Also found a clip was missing in dryer and door was hanging from hinges. Reseated everything and ensured proper functions. ; used 1 341241 ( BELT DRUM) from stock

We serviced a

SAMSUNG DRYER

Model DV448AEP/XAA

Near Havelock, North Carolina 28532

Davon

Job Details: 04/17/2026

Dryer not starting. Unit hums but will not turn. Only able to turn drum one way by hand. Found sock in blower wheel and excessive lint. Removed lint and sock. Confirmed that unit is now running correctly and heats. A dryer vent can also be installed as a separate job. It would include an exposed solid metal vent behind the dryer going through two shelves and Sheetrock. Venting would continue through attic and end in a soffit vent.

We serviced a

SAMSUNG WASHER FRONT LOA

Model WF42H5000A2

Near New Bern, North Carolina 28562

Greg Glade

Job Details: 04/17/2026

Customer reports no spin and agitate. Found inverter is supplied 120vac and has pwm signal of 4.9 vdc. Motor windings are 12 on all 3. Failed inverter board.

We serviced a

KENMORE WASHER

Model 11026882502

Near New Bern, North Carolina 28560

Greg Glade

Job Details: 04/17/2026

Customer reports washer not spinning or agitating. Son apparently found that the door switch was stuck. Was able to recreate issue. Failing lid switch. Replaced lid switch and ensured proper operation. ; used 1 WP8318084 ( SWITCH - LID) from stock

We serviced a

GE WASHER

Model HTW240ASK6WS

Near Bayboro, North Carolina 28515

Greg Glade

Job Details: 04/17/2026

Customer reports not completing cycle. Ran spin and agitate in forced mode. Washer does spin drum got up to specified rpms. During agitate can hear it agitating but no movement in the agitator. There is a firmware update this is needed. Shifter does work, failed transmission. Recommend replacing.

We serviced a

GE WASHER

Model GFW850SPN4RS

Near New Bern, North Carolina 28562

Davon

Job Details: 04/17/2026

Unit will not go through wash cycle. Another technician diagnosed a failed main control board. 2 inverter board faults are present. Locked rotor and hertz/voltage error. Initially found varying voltage to inverter board. then when there was correct voltage to the inverter board washer did spin but was drawing up to 7 amps. Measuring speed correctly. ; ordrng 1 WH22X38837 (Inverter board)

We serviced a

LG REFRIGERATOR

Model LFXS26596S/04

Near Greenville, North Carolina 27834

Davon

Job Details: 04/17/2026

Did not cool down after replacing compressor. Freezer is 45F and refrigerator 55F. Unit is using 0.3 amps. Low side pressure 15 inHg and high side pressure 38 psig. After pressing test button once low side pressure dropped to 28 inHg. Cut cap tube after filter dryer and refrigerant came out. Good flow both ways through cap tube. Used qwikflush to clean out cap tube and high side line. Flushed with nitrogen as well. Put new filter dryer in and tested for leaks. Charged with 60 grams r600a after vacuum for 30 minutes at 30inHg. Unit drawing 1 amp and freezer temp dropped to 40F before I left.

We serviced a

SAMSUNG REFRIGERATOR SID

Model RF22M9581SG/AA

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/16/2026

Found that ice room error code is for fan. Fan not moving after trying to force start. Failed ice maker fan. Ordering new one. ; ordrng 1 DA31-00070E (Ice maker fan)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFTR1821TB0

Near Cove City, North Carolina 28523

Davon

Job Details: 04/16/2026

Installed new door gasket and ensured that it is sealing well. Installed new ice maker and ran test cycle. Confirmed that it is no longer leaking. ; used 1 241798231 (ICE MAKER) from stock

We serviced a

GE DISHWASHER

Model PDT795SBV8TS

Near Richlands, North Carolina 28574

Davon

Job Details: 04/16/2026

Unit is not starting. Confirmed that control board has 120 vac to it. Smarthq does not turn on when it is plugged into it. Checked for 13 volts going to UI and it is not present. Diagnosed failed control board. Control board is not available through my suppliers so it will need to be supplied through GE. ; ordrng 1 WD21X36560 (Main control board)

We serviced a

GE REFRIGERATOR

Model PFE29PSDASS

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/16/2026

Reports fridge not cooling. Found evaporator fan not running. Ff fan error code in smart hq. Failed fresh food fan. Replaced fan and ensured proper operation. ; used 1 WR60X26866 ( EVAP FAN MOTOR (NON-STANDARD SXS)) from stock

We serviced a

SAMSUNG REFRIGERATOR

Model RF24BB6600QL

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/16/2026

Customer reports ice maker not working, found frozen water line. Recommend replacing water manifold. Steamed out fill tubes and ensured proper fill. Customer opted to wait on full repair to see if it happens again.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHB2740PP8A

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/16/2026

Customer reports fridge not cooling. Found that evaporator was completely frozen over. Evaporator fan is running. Found defrost thermistor out of spec. Ran a forced defrost and it does defrost, also checked defrost thermostat and its closed. 0.00 ohms. Recommend replacing thermistor. Ordering thermistor and scheduling follow up. ; ordrng 1 808137001 (DEFROST LIMIT AND DEFROST EVAP0RATOR)

We serviced a

LG REFRIGERATOR

Model LFXS26596S/04

Near Greenville, North Carolina 27834

Davon

Job Details: 04/16/2026

Customer reported freezer not cooling at all and refrigerator too warm. On my arrival both compartments are 72F. Compressor and fans are running. Compressor is cool to touch. Checked low side pressure with compressor running and measured 18 psig. Diagnosed failed compressor. Installed new compressor and filter dryer. Pressure tested for bubble leaks and confirmed cap tube patency. Vacuum pulled for 30 minutes to 30 inHg. Charged with 60grams of R600A. Installed software update. Compressor runs and refrigerator is drawing 0.9 amps. ; used 1 WPW10143759 ( FILTER DRYER/DYE/R600A/MISC) from stock

We serviced a

KENMORE WASHER/DRYER CMB

Model 41783042300

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/16/2026

Customer reports belt ripped and thumping noise coming from dryer. Gave quote for repair kit. Customer wanted me to see if I can fix their range hood, the socket got pushed inside. Fixed the socket.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHW08

Near Pikeville, North Carolina 27863

Greg Glade

Job Details: 04/16/2026

Customer reports no cooling. Found that evaporator fan is not working, has 120 vac. Failed evaporator fan. Also customer reports ice on bottom of freezer. Clogged defrost drain. Also found broken ice bucket. ; ordrng 1 W11559968 (EVAP FAN MOTOR (NON-STANDARD TM REAR WALL)) and 1 WPW10670845 (Ice bucket)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRMF3636RW00

Near Pikeville, North Carolina 27863

Greg Glade

Job Details: 04/16/2026

Customer wanted to check out their ice maker. Ice maker has 120 vac, fills during forced fill cycle. However ice maker does not harvest. Failed ice maker. Ordering new ice maker and scheduling follow up. ; ordrng 1 W11692161 (I/M ASSY)

We serviced a

SAMSUNG DRYER

Model DVE50R5400V

Near Goldsboro, North Carolina 27534

Greg Glade

Job Details: 04/15/2026

Customer reports dryer will turn off after 5-10 minutes of running signaling its dry when its not on a normal cycle. Customer states on timed dry it completed the whole cycle. Found moisture sensor unplugged. Re connected and ensured proper operation.

We serviced a

GE DISHWASHER

Model GDT226SSL1SS

Near Farmville, North Carolina 27828

Greg Glade

Job Details: 04/15/2026

Customer reports not draining. Upon arrival water was found in bottom of dishwasher. Tested drain pump and dishwasher does drain. Ran a normal cycle to see if itll cycle water. Dishwasher does cycle water. Did find leaking coming from float switch. Would recommend replacing.

We serviced a

MAYTAG WASHER

Model MVW5430MW0

Near Farmville, North Carolina 27828

Greg Glade

Job Details: 04/15/2026

Customer reports washer not draining. Found burnt wire at drain pump. Quoted harness. Customer opted to fix wires and see if it holds up. Fixed wires and heat shrinked. Ended proper operation.

We serviced a

SAMSUNG DRYER

Model DV45H6300EG/A3

Near Washington, North Carolina 27889

Davon

Job Details: 04/15/2026

"Cleaned dryer vent on 2nd floor by climbing out on patio roof. Short vent, used 2 rods. Large amount of lint removed. Air flow 16 mph before cleaning and 24 mph after cleaning vent."

We serviced a

GE DRYER

Model FORGOT

Near Grimesland, North Carolina 27837

Greg Glade

Job Details: 04/15/2026

"Customer wanted to look at vent, see if it needed cleaning, recommended replacement for rigid material as they have flex. Gave quote for cleaning and replacement. ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)"

We serviced a

SAMSUNG REFRIGERATOR

Model RF220NCTASR

Near Bath, North Carolina 27808

Davon

Job Details: 04/15/2026

Installed new fan motor and confirmed proper operation. Good air flow in freezer and refrigerator. Reinstalled ice maker and evaporator cover in freezer.

We serviced a

GE REFRIGERATOR

Model GSS25GSHMCSS

Near Ayden, North Carolina 28513

Greg Glade

Job Details: 04/15/2026

"Customer reports no water coming from dispenser and no ice being made. Checked to see if water would dispense at valve. No dispensing coming from valve at all, no voltage when actuated either. Ice maker does harvest but no fill. Ohmed out water valves and ohms accordingly. Failed control."

We serviced a

WHIRLPOOL WASHER TOP LOAD

Model WTW5000DW3

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/15/2026

Customer reports extreme banging from washer. Able to recreate. Issue suspected to be transmission due to noise and spinning. Recommend replacement of washer.

We serviced a

FRIGIDAIRE REFRIGERATOR SID

Model FRSS26L3AF7

Near Havelock, North Carolina 28532

Davon

Job Details: 04/15/2026

"Installed new evaporator fan motor and confirmed proper operation. Also confirmed that air is blowing into refrigerator. ; pckd up 1 5304532557 (Motor, evap fan), ordrd 1 242018303 (Motor, condenser fan)"

We serviced a

KENMORE WASHER

Model ="79641262610"

Near Havelock, North Carolina 28532

Davon

Job Details: 04/15/2026

Installed new dispenser to tub hose and pressure hose. Routed hose and switched screw orientation so it would not repeat the same failure. Ran wash cycle and confirmed no leaks. ; pckd up 1 4738ER1004B (Tub to dispenser hose) and 1 MEJ62305104 (Pressure sensor hose)

We serviced a

MIDEA WASHER

Model MLV45N1BWW

Near Havelock, North Carolina 28532

Davon

Job Details: 04/14/2026

"Customer reports that washer is frequently out of balance, especially with small and medium loads. Water is in balance ring. Suspension rods work correctly. Unit is level. Put clothes in unit and selected rinse and spin. When unit started to spin it ramped up quickly and was out of balance. After about 5 seconds unit started to add water. This is not normal behavior and points to faulty logic on control board. Diagnosed failed control board. Unit also gives E3 error codes frequently. Will replace lid lock to prevent this in the future. ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #), rqstng P&A on 1 17438000001615 (Lid lock) and 1 17138000020922 (MAIN CONTROL)"

We serviced a

FRIGIDAIRE REFRIGERATOR SID

Model FRSS26L3AF7

Near Havelock, North Carolina 28532

Davon

Job Details: 04/14/2026

"Not cooling well after electrical problem with house. Someone was working on WiFi and got shocked. After that several outlets and the refrigerator quit cooling well. Found evaporator fan motor not running. After putting unit into test mode, confirmed that there is 120 VAC to fan and it is not running. Diagnosed failed evaporator fan motor. ; ordrng 1 5304532557 (Motor, evap fan)"

We serviced a

GE WASHER

Model GTWN4250D1WS

Near Farmville, North Carolina 27828

Greg Glade

Job Details: 04/14/2026

Customer reports washer not doing anything when hitting the start button. Lid switch is working. Checked if 120 vac available. Voltage not being applied at inverter. Flashing light on inverter is normal. Failed control. Customer opted to replace unit. ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)

We serviced a

WHIRLPOOL DRYER

Model WED6200SW1

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/14/2026

"Customer retires dryer not working, starts to dry and then stops. Found shorting happening on board. Extreme fire hazard. Failed control. Control not available anymore. Recommend replacing unit."

We serviced a

HOTPOINT REFRIGERATOR

Model HPS18BTNDRBB

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/14/2026

Reports noise coming from fridge. Found that the noise is coming from evaporator fan motor. Recommend replacing evaporator fan motor. Replaced fan motor and ensured proper operation. ; used 1 WR60X31522 ( EVAP FAN MOTOR (NON-STANDARD SXS)) from stock

We serviced a

FRIGIDAIRE REFRIGERATOR

Model PHS67EHSB6

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/14/2026

"Customer reports noise coming from fridge. Found the noise coming from condenser fan. Fan is running fine, found that its vibrating excessively. Failing fan motor. Customer opted to not repair."

We serviced a

HISENSE REFRIGERATOR

Model HRF266N6CSE

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/14/2026

Customer reports ice maker not making ice. Found that the ice maker is harvesting but not calling for water. Replacing ice maker under warranty. ; ordrng 1 K1944385 (Ice maker)

We serviced a

WHIRLPOOL RANGE

Model WEC310SAGB3

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/14/2026

"Customer reported beeping on unit. Found f2e1 error saved on board. Shorted keypad. Disconnected power to unit for 2-3 minutes, and reapplied power. Board still has error saved. Unit is still functioning. Bake and broil work and keypad is functioning. No signs of damage on p11 connector. Would recommend replacing main control if issue persists."

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS3

Near Havelock, North Carolina 28532

Davon

Job Details: 04/14/2026

Customer reports that after sink backed up unit would not wash the dishes. Error codes F8E2. In test mode wash motor does not run. Diagnosed failed wash motor. Recommend using Affresh or citric acid to prevent motor failure in the future. ; ordrng 1 W11416362 (Sump assembly)

We serviced a

WHIRLPOOL REFRIGERATOR SID

Model WRS555SIHZ06

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/14/2026

Customer reports fridge not making ice. Found fill tube frozen. Very slight leak coming from fill tube. Failing water valves. Recommend replacing. Installed new valves and ensured proper operation. ; pckd up 1 WPW10179146 (VALVE - DOUBLE COIL)

We serviced a

GE WASHER

Model GTWN4250D1WS

Near Farmville, North Carolina 27828

Greg Glade

Job Details: 04/14/2026

We serviced a

FRIGIDAIRE DRYER

Model FFQE5000QW1

Near New Bern, North Carolina 28560

Davon

Job Details: 04/13/2026

Cleaned dryer vent. Removed moderate amount of lint. Confirmed proper operation. Air flow 15 mph after cleaning. Offered semirigid vent for behind dryer. Dryer also turned off while cleaning and determined that the cause of this was a faulty wall plug. Recommended to customer that he have wall plug replaced.

We serviced a

WHIRLPOOL RANGE

Model WFE540HOES0

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/13/2026

Customer reports bake not working but broil working. No amp draw on element. Found bake element testing at 15mohms. Diagnosted failed element. Replaced element and ensured proper operation. ; used 1 W10779716 ( ELEMENT - BAKE (CONCEALED)) from stock

We serviced a

WHIRLPOOL REFRIGERATOR SID

Model GC3JHAXTS01

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/13/2026

Customer reports leaking coming from bottom left corner on freezer. Found ice buildup on bottom of freezer, clogged defrost drain. Cleared drain and ensured proper flow.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FGHB2866PFNA

Near Farmville, North Carolina 27828

Greg Glade

Job Details: 04/13/2026

Customer reports water leaking from freezer. Found clogged defrost drain. Cleared drain and ensured proper operation.

We serviced a

GE REFRIGERATOR

Model GFE28GYNGFS

Near Chocowinity, North Carolina 27817

Davon

Job Details: 04/13/2026

Put new start device in place. Compressor does not start today. Confirmed that testing start device is not working now either. Apparently compressor problem is intermittent. Diagnosed failed compressor.

We serviced a

FRIGIDAIRE DRYER

Model FASE7073LA0

Near Kinston, North Carolina 28504

Greg Glade

Job Details: 04/13/2026

Installed new motor and ensured proper operation.

We serviced a

WHIRLPOOL WASHER TOP LOAD

Model WTW8040DW1

Near Washington, North Carolina 27889

Davon

Job Details: 04/13/2026

For the last 3 weeks washer has been intermittently making a squealing noise when spinning. Yesterday it became constant. Error code stored F2E1 for stuck key. Unable to reproduce the noise, but noticed rust sprayed on appliance apron from motor. This is caused by a leaking transmission seal. Diagnosed failed transmission. Would also need new slider.

We serviced a

KENMORE MICROWAVE OVER T

Model 721.86013010

Near Jacksonville, North Carolina 28540

Greg Glade

Job Details: 04/13/2026

Customer reports buttons not working on microwave, found that the mounting bracket is broken. Failed panel. Would need to replace panel to fix issue. Part is no longer available.

We serviced a

SAMSUNG DRYER ELECTRIC

Model DVE54M8750V/A3

Near Greenville, North Carolina 27834

Davon

Job Details: 04/13/2026

Installed new dryer vent hood and cleaned short vent. Air flow 23.5 mph.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Farmville, North Carolina 27828

Davon

Job Details: 04/13/2026

Installed new evap fan motor, defrost thermostat, thermistor, and wiring harness. Confirmed proper operation of fan.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFTR1821TB0

Near Cove City, North Carolina 28523

Davon

Job Details: 04/10/2026

Refrigerator door not closing correctly. Found broken refrigerator door gasket. Also noted rime ice in freezer caused by air leak from refrigerator door gasket leaking. ; ordrng 1 242193212 (Refrigerator door gasket)

We serviced a

WHIRLPOOL DRYER ELECTRIC

Model WED8000DW4

Near Washington, North Carolina 27889

Davon

Job Details: 04/10/2026

Installed new blower wheel and confirmed proper operation.

We serviced a

WHIRLPOOL DRYER

Model WED4815EW1

Near Washington, North Carolina 27889

Davon

Job Details: 04/10/2026

Quote for dryer vent. Vent is currently venting under the house. Quote is for solid metal venting installed in crawlspace, new vent hood/flap, and new connections to dryer. Includes drilling through brick wall.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Farmville, North Carolina 27828

Davon

Job Details: 04/10/2026

Not cooling well in refrigerator. Freezer temp 3-15F. Refrigerator 55F. Found evaporator fan not turning. It does have 10.7 volts going to it. Diagnosed failed evaporator fan motor. ; ordrng 1 W11578030 (Evap fan motor, wiring harness)

We serviced a

WHIRLPOOL WASHER

Model WTW5540SQ0

Near Winterville, North Carolina 28590

Davon

Job Details: 04/10/2026

Unit is out of balance. Unit does spin with no difficulty with no clothes. Springs are weak. Will replace counterweight and suspension springs.

We serviced a

SAMSUNG REFRIGERATOR

Model RF25HMEDBSG/AA-03

Near Greenville, North Carolina 27834

Davon

Job Details: 04/10/2026

Took out old filter and put in new one.

We serviced a

WHIRLPOOL DRYER ELECTRIC

Model WED4815EW1

Near Winterville, North Carolina 28590

Davon

Job Details: 04/10/2026

"Dryer not spinning. Found broken belt. Belt looks like it was deteriorated, possibly from heat. Found vent outside plugged with lint sheet. Also noted that there was a lot of lint that had collected past lint screen in dryer. Disassembled dryer to clean all lint out of lint trap area. Cleaned dryer vent and shortened semi rigid vent behind dryer. Cleaned dryer vent, approximately 10 straight feet of vent. ; pckd up 1 341241 (BELT,DRIVE)

We serviced a

SAMSUNG WASHER

Model WA45N3050AW/A4

Near Kinston, North Carolina 28504

Greg Glade

Job Details: 04/09/2026

Customer reports no spin happening. Found that belt on drive shaft is extremely loose, had no tension in it at all. Diagnosed failed belt. ; ordrng 1 DC66-10170B (BELT)"

We serviced a

FRIGIDAIRE DRYER

Model FASE7073LA0

Near Kinston, North Carolina 28504

Greg Glade

Job Details: 04/09/2026

Customer reports humming coming from dryer. Checked all fuses and circuits regarding the motor. E52 error code, checked if motor thermal cut off was tripped, it wasnt. Motor consistently hums. Dryer has 240 vac, supply voltage isnt the issue. Diagnosed failed motor.

We serviced a

LG WASHER

Model DLE3400W

Near Havelock, North Carolina 28532

Davon

Job Details: 04/09/2026

Installed new belt and confirmed proper operation.

We serviced a

GE WASHER

Model GTW465ASN3WW

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/09/2026

Customer reports water agitator fell off. Upon arrival agitator snapped off with the transmission. Would need new agitator and transmission to fix. Recommend replacing.

We serviced a

BOSCH REFRIGERATOR

Model B36CL80SNS/44

Near New Bern, North Carolina 28560

Davon

Job Details: 04/09/2026

Intermittently not cooling well in freezer. Temp will go up to 17F in freezer per customers sensor that he has in it. Noted a large amount of rime ice on back wall of freezer. Apparently doors have been sticking open .Error e9050, e9130. Steamed out freezer and reinstalled drawers.

We serviced a

LG REFRIGERATOR BOT

Model LFX25971ST

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/09/2026

Customer suspected leaking coming from fridge. Checked fridge found no leaking. Compressor was extremely hot though with a 1.2 amp draw. Would suspect a leak potentially to attribute to the hot compressor and high amp draw.

We serviced a

WHIRLPOOL WASHER TOP LOAD

Model WTW4816FW3

Near Goldsboro, North Carolina 27530

Greg Glade

Job Details: 04/09/2026

Customer reports drain pump turning on when plugging unit in. F3e1 error found saved on control board. F7e6 and f8e1 also found. Motor and no/long fill. Ran automatic test cycle and calibration cycle. Functioned as it should. Diagnosed failed control board. Installed new board and no errors saved on unit. Ran calibration on unit. Ensured proper operation. ; pckd up 1 W11603810 (CONTROL BOARD, MAIN)

We serviced a

SAMSUNG REFRIGERATOR SID

Model 097F43BJ400018W

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/09/2026

Installed new bucket and clip and ensured proper seal. ; pckd up 1 DA82-01397A (I/M ICEMAKER)

We serviced a

LG DRYER

Model DLE3500W

Near New Bern, North Carolina 28560

Davon

Job Details: 04/09/2026

Quoted dryer vent. Vent is currently a PVC pipe opening into basement. Quote includes replacing all venting with rigid vent. Drill hole through masonry and cultured stone. Does not include stonework needed around vent after perforation. Sheetrock in garage will also need to be removed and replaced. Quote includes putting old Sheetrock back in place after removing it. ; schdld next appmnt for 4/14 TUE !

We serviced a

WHIRLPOOL DRYER ELECTRIC

Model WED8000DW4

Near Washington, North Carolina 27889

Davon

Job Details: 04/08/2026

Dryer not turning. Found piece of clothing stuck in blower wheel. Removed clothing and cleaned wheel. After unit ran for about 15 minutes while cleaning vent, heard vibrating noise. Took it apart again and found broken blower wheel. Ordering blower wheel. ; ordrng 1 WP697772 (Blower wheel), pckd up 1 279640 (PULLEY,IDLER)

We serviced a

GE DRYER

Model GFD85ESPN1RS

Near Washington, North Carolina 27889

Davon

Job Details: 04/08/2026

Installed new dryer vent cover and two air intake covers.

We serviced a

BOSCH REFRIGERATOR

Model B22CT80SNS01

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/08/2026

Customer reported dispenser not working. Found water line frozen. Defrosted the water line and ensured proper operation.

We serviced a

GE DISHWASHER

Model gdp665syn8fs

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/08/2026

Installed new sensor and dishwasher went into flood mode and the ftd error. Thoroughly cleaned old sensor and put back on washer and it ran perfectly fine. Ran 1 hour wash and waited to see if error would throw. It didnt. Would potentially replace control again if issue persists.

We serviced a

WHIRLPOOL DRYER ELECTRIC

Model WED8000DW4

Near Washington, North Carolina 27889

Davon

Job Details: 04/08/2026

Flex vent in crawlspace. 11.3 mph air flow before cleaning. Offered replacement or cleaning. Customer opted for dryer vent cleaning. Used 3 rods. Large amount of lint removed. 16.2 mph air flow after cleaning.

We serviced a

GE REFRIGERATOR

Model GFE28GYNGFS

Near Chocowinity, North Carolina 27817

Davon

Job Details: 04/08/2026

Not cooling. Compressor is starting and then overload clicks off. Used testing start device and confirmed that compressor runs for over 5 minutes and draws 0.9 amps. Confirmed that capacitor measures 12 uF. Diagnosed failed start device. Ordered start device.; ordrng 1 WR07X10131 (RELAY/OVERLOAD)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHS2611PFEA

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/08/2026

Found frozen water line. Defrosted and ensured proper operation.

We serviced a

SAMSUNG REFRIGERATOR

Model RF220NCTASR

Near Bath, North Carolina 27808

Davon

Job Details: 04/08/2026

Tenant reports that unit is not cooling in refrigerator section. Refrigerator 65F. Found freezer section 16F near the top and -3F near the bottom. In diagnostic mode, FZ fan error is showing. Took evaporator cover off of freezer and found fan seized. Difficult to turn by hand. Diagnosed failed fan. ; ordrng 1 DA31-00334C (Fan motor)

We serviced a

GE MICROWAVE OVER T

Model JVM7195SK6SS

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/07/2026

Customer reports microwave not working. No amp draw at all. Found stuck door switch. After reseating door switch, microwave light comes back on and has 13 amp draw. Microwave working as it should.

We serviced a

WHIRLPOOL REFRIGERATOR

Model GX5SHDXTQ00

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/07/2026

Customer reports no cooling in entire unit. No amp draw on compressor. Used cheater cord and compressor does run. Failed start device. Put new device on and ensured proper operation and amp draw. ; used 1 W10613606 ( COMPRESSOR RELAY/OVERLOAD ASSM) from stock

We serviced a

FRIGIDAIRE RANGE GAS

Model PLCS389ECG

Near Grimesland, North Carolina 27837

Greg Glade

Job Details: 04/07/2026

Customer reports smelling gas. Found that leak is coming from stove shut off valve in the back. Needs gas company to come and fix leak.

We serviced a

LG REFRIGERATOR

Model LFX31925ST

Near Winterville, North Carolina 28590

Davon

Job Details: 04/07/2026

Er Rf since cleaning defrost drain in refrigerator yesterday. Found evaporator cover unplugged. Plugged it back in. Unplugged refrigerator to reset error code.

We serviced a

GE WASHER

Model GTW465ASN9WW

Near Pikeville, North Carolina 27863

Greg Glade

Job Details: 04/07/2026

Customer reports a noise coming from washer. Like a grinding noise. Force ran agitate and spin cycles. Unable to pull pulsator off. Able to recreate issue, noise coming from transmission. Falling transmission. Customer opted to replace unit.

We serviced a

FRIGIDAIRE REFRIGERATOR BOT

Model FGHB2866PFGA

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/06/2026

Complaint of no ice. Found no water in ice bucket, tried to force harvest and does force harvest. Reset ice maker and told customer that it should produce ice in about 4-6 hours. Suspect issue is with the temperature of the unit. Would potentially need the air handler kit.

We serviced a

SAMSUNG REFRIGERATOR SID

Model 097F43BJ400018W

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/06/2026

Customer reported leaking after getting ice. Found that a small puddle would formulate in the chute. Humid air is leaking into ice maker from somewhere. Found that there ice maker bucket itself is not sealing well and has multiple cracks in it. Although seal around the ice maker bucket looks fine, it is not seating properly. Ordering new bucket and latch. ; ordrng 1 DA82-01397A (I/M ICEMAKER)"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHS2611PFEA

Near Greenville, North Carolina 27834

Greg Glade

Job Details: 04/06/2026

Installed new water valves and ensured proper operation.

We serviced a

FRIGIDAIRE RANGE

Model NOT AVAILABLE

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/06/2026

Installed new element and ensured proper operation.

We serviced a

MAYTAG WALL OVEN

Model CWE5800ACE

Near Greenville, North Carolina 27858

Greg Glade

Job Details: 04/06/2026

Installed new board and ensured proper operation. ; pckd up 1 74001404 (REFURBISH CONTROL BOARD)

We serviced a

KENMORE DRYER

Model 796.81962.710

Near Winterville, North Carolina 28590

Greg Glade

Job Details: 04/06/2026

Customer reports g80 error. Customer has had vent cleaned, thermistor tests setting specifications. Tested air flow out of dryer and with lint screen its about 15-18. Without it is about 18-22. A little discrepancy. Noticed though that the air flow isnt a consistent stream it will vary in mph. Would recommend soaking the lint screen to clean and try running without the screen to see if itll trip.

We serviced a

AMANA WASHER

Model NTW4516FW3

Near Kinston, North Carolina 28501

Greg Glade

Job Details: 04/06/2026

Found failed damper system. Replaced dampers and ensured proper operation. ; used 1 W10780045 ( DAMPERS) from stock

We serviced a

MAYTAG DRYER ELECTRIC

Model MED5630HC2

Near Kinston, North Carolina 28504

Greg Glade

Job Details: 04/03/2026

Rattling noise coming from dryer. Quoted a dryer repair kit. Oiled and cleaned the wheels and outlet as everything looked relatively new. Fixed issue. Left quote if issue happens again soon.

Contact Us Today

Learn More About Us